PAINT
High quality, heat resistant paints that match OEM trim colors.
Excellent adhesion and resistance to the suns ultraviolet rays
Our fastest curing clear for spot repairs, cut-ins, jambs and single panel jobs where a fast delivery is key. Sand and buff as quickly as 45 minutes and deliver in 2-3 hours, AIR DRY!
4:1 Mix ratio with MACH 1 Activator. 4.2 VOC ready to spray.
Gallon
CLEAR COAT UPOL
EUROPEAN STYLE CLEARCOAT with NANO PARTICULATE TECHNOLOGY !Features & Benefits:
• Easy to apply with excellent flow and
non-sag properties
• Hardens rapidly to give a high build U.V resistant
coating.
•Excellent gloss and long term durability
• Can be air dried, low baked or I.R. cured
• Can be easily polished once cured
Nano Particulate Clear Features:
• The SRC resins provide improved scratch and
• abrasion resistance
• Deep wet-look gloss and transparency
• 72 hour buff window
• Barrier against gases, water and solvents
• Increased weather resistance (acid rain)
• Reduced shrinkage and heat reaction
• Improved adhesion to ALL substrates
• Better dirt resistance
• HS ... Higher solids
• Solvent and Water Borne compatible
VOC-compliant Castle® Engine Enamel contains no fluorocarbons, vinyl chloride, methylene chloride, or lead.
The paint is non-toxic when dry.
Resists heat up to 500°F.
Castle® offers a wide range of colors.
Consult a paint chart for specific colors
1. Make sure surfaceto be painted is clean and dry.
2. Shake well and use at room temperature (70°F)
3. Hold can 10 to 12 inches from surfaces.4. Remember that two thin coats are best.
5. If recoating is required, apply second coat as soon as first coat is dry (about 15 minutes)
ENGINE PAINT
Castle
®Cast Iron Gray Paint is created especially for engine re-builders. It is fast drying, leaving a hard tough film that makes the rebuilt
part look factory fresh. The tough finish resists heat, gasoline, grease, oil, and moisture. It will not harm cylinder walls.
Uses:
Designed for engine re-builders but can be used wherever desired for painting a surface.
Directions:
1. Be sure surface is clean and dry.
2. Mask off area to be painted.
3. Shake well (mixing ball should move freely for
one minute).
4. Use at room temperature.
5. Hold can 6-8 inches from surface.
6. Use overlapping strokes. Two thin coats are better than one heavy coat.
16oz AEROSOL
JAMB-IT Clear is a convenient, fast-drying
acrylic clearcoat for use on door jamb areas,
under the hood, trunk areas & small spot
repairs. Provides excellent gloss, clarity &
image depth.
Directions:
1. Make sure surface to be painted is clean and dry.
2. Shake well and use at room temperature.
3. Hold can 10 to 12 inches from surface.
4. Remember that two thin coats are best.
5. If re-coating is required, apply second coat as soon as first is dry. (about 15 minutes)
16oz AEROSOL
TRIM PAINT
High quality, heat resistant paints that match
OEM trim colors. Excellent adhesion and
resistance to the suns ultraviolet rays
16oz AEROSOL
FLAT BLACK ENAMEL
SEMI-GLOSS BLACK ENAMEL
GLOSS BLACK ENAMEL
GLOSS WHITE ENAMEL
SEMI-GLOSS BLACK LACQUER
SILVER TONE LACQUER
CLEAR GLOSS LACQUER
TRIM PAINT
Matches OEM finish for automotive
exterior trim. Provides superior
adhesion to stainless, chrome,
steel, aluminum. Will not crack
or peel. No primer required.
GLOSS BLACK
12oz AEROSOL
UNDERHOOD PAINT
NU-LOOK FLAT BLACK
|
Castle® Nu-Look Paints™ are fast
drying and provide excellent coverage. They are formulated for professional automotive reconditioning applications under the hood and under the car, where high temperature engine paint or heater paint is not required. |
| Directions: |
|
FLAT BLACK
16oz AEROSOL
