Time-Sert Triton Repair Professional Ford Sparkplug M14x1.25 Thread Repair Kit

TIME-SERT® PROFESSIONAL FORD SPARK PLUG M14x1.25 THREAD REPAIR KIT

Repairs ford heads with a straight section between the threads and taper seat.
Models F-150 can be 1.9, 3.0, 4.6, 5.4, 6.8 liter engines. (click here for inserts type)
Used in 2 valve or 4 valve heads

WORLD'S BEST FORD SPARK PLUG THREAD REPAIR KIT P/N 6605553
Your permanent repair for Ford spark plug blow outs.

6605553

click for larger view

	1	66255511	Wrench
	1	66255512	Reamer
	1	66255513	Tap
	1	66255514	Driver
	1	66255515	Setting tool
	1	66255516	hex key 1/8
	1	66255518	Triton Counterbore
	1	66251487	hex key 3/16
	1	6626020	Sealer
	5	66151459	Triton Inserts M14x1.25
Use kit number 6605553-8 for 8 inserts 6605553 only includes 5

Repair video on section view head Click here
This repair is considered "over the fender" you do not have to remove the head.

INSTRUCTIONS

Stop: Check that the valves are not open!

The only 100% way to know the valves are not open is to remove the valve cover and inspect
the cam, making sure that it is not depressing the valves on the damaged spark plug hole.

This kit not recommend for holes larger than .640 inches or 16.3mm

An optional way to check that the valves are closed, this is a 2 man job.
Have someone turn the engine over by hand with a 18mm socket from the front of the engine.
Turn the engine over until it is going up on the compression stroke. Place your thumb at the
top of the spark plug hole at the same time to block off the air. When you feel the engine
compression stop pushing air against your thumb the piston will be top dead center. Turn the
engine a little more to be on the down stroke, both valves should be closed at this point, and
the piston should be out of the way.

-------------------------------------------------------------------------------------------------------------------------------------

PAGE 1

A: Using the wrench provided, tighten the set screw to secure the counterbore in place. Counterbore the hole to the full depth permitted by the tool P/n 66255518 picture A: until the counterbore bottoms out on the hole and spins freely. NOTE: Some engines will require more metal to be removed with counterbore tool than others ( e.g. 2001 and up 1L2E heads) Click here for more info. TIP: Packing the flutes with grease will help to catch stray chips from going into the cylinder. B: Place the Reamer into the square of the wrench and tighten the setscrew to secure the reamer in place.

Ream the hole picture C: until black "Stop Collar" touches head. This will create the 45 degree countersink seen in picture D: When you start getting close to the stop collar coming in contact with the head, you will want to clean the chips from the reamer so you will have a positive stop on the head without having any chips interfering. The reamer should spin very freely when the collar touches the head.
	TAP THE HOLE Tap the hole with the wrench provided. There is a pilot at the front of the tap to help guide it straight into the hole. Use contact or break cleaners to thoroughly clean out any remaining chips and oil.
Mechanics Tip 1: Packing the flutes with grease will help to catch any stray chips from going into the cylinder. Mechanics Tip 2: Using a shop-vac with a thin hose taped to the nozzle is helpful removing any remaining chips in the cylinder.

Setting Tool A: Screw the setting tool into the insert B: Lightly tighten the socket cap screw

Using the wrench provided place the setting tool into the wrench Place the Locktite around the middle of the insert and into the clean prepared hole Screw the insert into the hole until the flange of the insert is seated into the head. This is approximately 20 foot pounds.

Hold the wrench, and in a counter-clockwise rotation, loosen the cap screw with the allen key provided. This will allow the setting tool to release itself from the insert. You can now remove the setting tool from the insert.

INSERT THE DRIVER TOOL Using the wrench provided, place the driver tool into the square and tighten the setscrew to secure the driver in place. Oil the bottom threads of the insert driver with a few drops of driver oil.

Screw the driver into the insert. The driver will cold form the last few threads of the insert. This is approx. 10 full turns. While screwing the driver into the insert you will feel the driver start to tighten up, with a little more power continue through the insert until it loosens up. Remove driver, repair is complete. ---------------------------------------------------------------------------------------- note: Using an air ratchet for counterbore and reamer tools will help speed up the operations, but is not recommended for tapping or driver tool.